Well Pump Not Working? Troubleshooting Guide for Homeowners
When a well pump stops working, the cause is often simple: a tripped breaker, a stuck pressure switch, a waterlogged pressure tank, or a clogged filter. About 13 million American homes rely on private wells, and most pump problems show up as one of three symptoms — no water at all, a pump that runs constantly or cycles on and off, or low water pressure. Work through the checks in this guide before calling a professional, and you may fix the problem in minutes. But if the breaker keeps tripping, the pump hums without starting, or the pump is over 15 years old, it is time to call a well specialist.
How a Well Pump System Works
About 13 million American homes get their water from a private well, and the well pump is the heart of that system. A submersible pump sits deep in the well, pushing water up into a pressure tank in your home. The pressure tank stores water under pressure — usually 40 to 60 psi — so your taps have steady flow without the pump running every time you open a faucet. A pressure switch on the tank tells the pump when to turn on (typically at 40 psi) and when to shut off (at 60 psi). When any part of this chain fails — the pump, the switch, the tank, or the wiring — the symptoms show up fast: no water, weak pressure, or a pump that runs nonstop. The good news is that many well pump problems have simple causes you can check yourself before calling a plumber.
No Water at All? Check These First
If you turn on a tap and nothing comes out, work through these checks in order before assuming the pump is dead:
- Check the circuit breaker: a tripped breaker is the most common cause. Reset it once — if it trips again immediately, there is an electrical fault and you should call a professional.
- Check the pressure switch: look for the small grey box on the pressure tank. If it has a low-pressure cutoff lever, hold it in the "start" position for a few seconds to restart the pump.
- Check the pressure gauge on the tank: if it reads zero and the pump is not running, the problem is electrical or the pump itself. If it reads normal pressure but no water flows, the problem is downstream, such as a closed valve or a frozen pipe.
- Check for a tripped GFCI outlet or a blown fuse if your pump is on a dedicated circuit with its own protection.
- Look and listen: a pump that hums but does not start may have a failed start capacitor or a seized motor; a pump that makes no sound at all is likely not getting power.
- Check the water level: in a drought or after heavy use, a well can temporarily run dry. Wait a few hours and see if the water returns before assuming the pump has failed.
Pump Runs Constantly or Cycles On and Off
A pump that never shuts off is usually fighting a leak or a failed pressure switch. If the switch contacts are burned or stuck, the pump keeps running even after the tank reaches pressure — listen for a pump that runs long after all taps are closed, and check whether the pressure gauge climbs past 60 psi. If the pressure stays low while the pump runs, water is escaping somewhere: a leak in the underground line, a failed check valve letting water drain back into the well, or a cracked pipe. Short cycling — the pump turning on and off every few seconds — is usually a waterlogged pressure tank. The tank's air bladder has failed, so there is no cushion of air to hold pressure, and the pump starts with every small demand. A waterlogged tank also shows up as pressure that surges and drops at the tap. Both problems waste electricity and wear out the pump fast: a pump that short-cycles can burn out in months instead of lasting its normal 10 to 15 years.
Low Water Pressure From a Well
Low pressure has several possible causes, and the fix depends on which one you find. First check the pressure gauge: if the tank reads 40 to 60 psi but the taps are weak, the problem is after the tank — a clogged filter, a partially closed valve, or sediment buildup in the pipes. Whole-house filters clog faster on well water, so a filter change is the cheapest first step. If the gauge itself reads low, the pump may be losing capacity: mineral buildup on the pump, a worn impeller, or a dropping water table all reduce output. Check the pressure switch settings too — the cut-in and cut-out pressures may have drifted, or the small tube that senses pressure may be clogged with sediment, which makes the switch read incorrectly. Cleaning that tube with a thin wire often restores normal operation. If pressure drops only when several fixtures run at once, the pump may simply be undersized for the house, or the well's recovery rate may be too low.
Strange Noises, Air in the Lines, and Dirty Water
Air spurting from taps, cloudy water, or grit in the water usually means the water level in the well has dropped close to the pump intake, letting the pump suck air. Let the well rest and reduce water use; if the problem persists, the pump may need to be lowered or the well may need deepening. A rattling or grinding noise from the pump often means worn bearings or sand in the pump — sand is common in new or shallow wells and wears pumps out quickly, so a sediment filter is worth installing. Black or orange water points to iron or manganese in the water, not a pump fault, and is handled with filtration. A sulfur or rotten-egg smell comes from hydrogen sulfide gas in the well water. None of these mean the pump is necessarily broken, but they all deserve a professional look if they appear suddenly.
When to Call a Professional — and What Repairs Cost
Call a plumber or well specialist if the breaker keeps tripping, the pump hums but will not start, the pump is more than 15 years old, or you suspect the well itself is the problem. Pulling a submersible pump requires special equipment — the pump can sit 100 feet or more down the well — and working on well wiring is dangerous without the right training. Typical costs: a pressure switch replacement runs $150 to $400, a pressure tank replacement $400 to $1,000, and a new submersible pump $1,000 to $2,500 installed, depending on depth. A full pump and tank replacement can reach $3,000 or more. Most well pumps last 10 to 15 years, so if yours is in that range and keeps failing, replacing it is usually smarter than another repair. Keep a record of the pump's age, depth, and model — it makes every future diagnosis faster and cheaper.
When to Call a Professional
Call a well specialist if the breaker keeps tripping, the pump hums but will not start, the pump short-cycles constantly, the well runs dry, or the pump is over 15 years old. Pulling a submersible pump needs special equipment and should not be attempted by a homeowner.
What a Plumber Will Do
A well specialist tests the electrical supply, checks the pressure switch and tank, measures the pump's output, and pulls the pump if needed to inspect or replace it — then restores pressure and verifies the whole system holds steady.
Frequently Asked Questions
How long does a well pump last?
A submersible well pump typically lasts 10 to 15 years, and a jet pump 8 to 10 years. Hard water, sand in the well, and frequent short cycling shorten that life. A pump that has run well for over 15 years is living on borrowed time — budget for a replacement before it fails without warning.
Why does my well pump keep tripping the breaker?
The most common causes are a shorted pump motor, a failed start capacitor, damaged wiring down the well, or a pump seized by sand or mineral buildup. Reset the breaker once; if it trips again, do not keep resetting it — call a professional, because a short in a submersible pump is a job for a specialist.
How do I know if my well is running dry?
Signs include air spurting from taps, water that turns cloudy or gritty, and a pump that runs longer and longer to build pressure. Turn off all water use for several hours and see if the well recovers. If it does, the well's recovery rate is low and you may need to conserve water or deepen the well.
How much does well pump repair cost?
A pressure switch replacement costs $150–$400, a pressure tank $400–$1,000, and a new submersible pump $1,000–$2,500 installed. A complete pump and tank replacement can reach $3,000 or more, depending on well depth and access.
Can I replace a well pump pressure switch myself?
A handy homeowner can replace a pressure switch, but the power must be shut off at the breaker first and the wiring done exactly as the old switch was wired. If you are not confident working with 240-volt wiring, leave it to a professional — a wiring mistake can destroy the pump or cause a shock.
