water treatment
Well Pump Repair, Replacement & Pressure Tank Service
When your well pump fails, your home has no water — no showers, no flushing, no cooking, no drinking water. For the millions of rural American homes that rely on private wells, the well pump is the most critical piece of plumbing in the house, and when it stops, every hour matters.
A well pump draws water from your well and delivers it to your home. Submersible pumps sit deep inside the well casing and push water up — they are the most common type for modern wells. Jet pumps sit above ground and pull water up by suction, and are used for shallower wells. Either way, the pump works with a pressure tank, which stores water under pressure so the pump doesn't have to run every time you turn on a tap, and a pressure switch, which tells the pump when to turn on and off. Because well work involves electricity, deep wells, and heavy equipment, it should always be done by a qualified professional.
Signs You Need Well Pump Services
- No water at all — the most urgent sign, caused by a failed pump, tripped breaker, or bad pressure switch.
- Low water pressure throughout the house — a weakening pump, a waterlogged pressure tank, or a clogged filter can all cause it.
- The pump runs constantly or cycles on and off rapidly — short cycling usually means a failing pressure tank or a leak in the system.
- Air sputtering from faucets — air in the lines can mean the water level has dropped below the pump intake.
- Your pump is 10–15 years old — most well pumps last 10–15 years; older pumps fail without warning.
Our Process
Diagnosis
The plumber checks the breaker and pressure switch, tests the pressure tank's air charge, measures water pressure, and checks the pump's electrical draw.
Upfront Quote
You get a clear price for the repair or replacement — pump, tank, switch, or controls — before work begins.
Repair or Replacement
The plumber replaces the faulty part, or pulls and replaces the pump if it has failed, and re-pressurizes the tank.
Testing
The system is run to confirm steady pressure, correct pump cycling, and clean water at every tap.
What Affects the Cost
- Replacing a pressure switch or control box typically runs $200–$500.
- A new pressure tank usually costs $800–$2,500 installed, depending on size.
- Replacing a submersible well pump generally runs $1,500–$4,000, depending on the well's depth, the pump's horsepower, and how hard the pump is to pull. Jet pump replacement is usually less, around $800–$2,000.
- Well depth, pump type and horsepower, whether new wiring or piping is needed, and local rates all affect the final price.
- Costs vary by location and job; your plumber provides an exact quote after an on-site diagnosis. Emergency or after-hours service typically carries a surcharge of $50–$150 or 1.5–2x the standard rate.
✓ Safe to DIY
- Check your pressure tank's air charge annually — a waterlogged tank makes the pump short-cycle and wear out early.
- Test your well water yearly for bacteria, nitrates, and minerals.
- Listen for short cycling — a pump that clicks on and off constantly is telling you something is wrong.
- Keep the wellhead clear and capped — debris and surface water around the wellhead contaminate your water.
✕ Stop & Call Us
- Never attempt to pull or replace a submersible well pump yourself — it requires specialized equipment, and well work involves high-voltage electricity and heavy components.
- Do not keep resetting a breaker that trips repeatedly — it signals a fault that needs professional diagnosis.
- Do not open the well casing or work around the wellhead wiring without a qualified professional.
Frequently Asked Questions
How long does a well pump last?
Most submersible well pumps last 10–15 years. Jet pumps typically last 8–12 years. A well-maintained pressure tank and clean water help a pump reach the top of that range.
Why does my well pump keep turning on and off?
This is called short cycling, and the most common cause is a waterlogged pressure tank that has lost its air charge. It can also mean a leak in the system or a failing pressure switch. Short cycling wears out pumps fast — get it checked promptly.
Can I replace a well pump myself?
No. Pulling a submersible pump from a deep well requires specialized equipment, and well work involves high-voltage electricity and heavy components. It should always be done by a qualified professional.
What should I do if I have no water at all?
Check your breaker panel first — a tripped breaker is a common cause. If the breaker is fine, call (619) 782-6581 for emergency dispatch. Don't keep resetting a breaker that trips repeatedly.
Related Services
Request Service
Step 1 of 3- Upfront pricing — no surprise charges
- Licensed, background-checked plumbers
- Cleanup included on every job
Need a Trusted Plumber Fast?
From 24/7 emergency repairs and drain clearing to water heater replacements and leak detection, licensed plumbers across the USA are standing by.

