Trusted Plumbing Services Nationwide • Licensed & Insured Plumbers Across the USA
Water Heaters

Water Heater Maintenance & Flush Guide

Updated on November 14, 2026
Quick Answer:

Flushing your water heater once a year removes sediment that reduces efficiency, causes rumbling noises, and shortens the tank's life. The job takes about an hour, needs only a garden hose and a bucket, and can add years to your water heater.

Why Flush Your Water Heater

Sediment — minerals from your water, especially in hard-water areas — settles at the bottom of the tank over time. It insulates the water from the heating element or burner, forcing the heater to work harder, raising energy bills, and causing rumbling or popping noises. Left unchecked, sediment accelerates corrosion and can cut years off the tank's life. Most manufacturers recommend flushing once a year; twice a year in very hard-water areas.

Safety First

Water inside the tank is hot enough to cause serious burns, and gas and electric heaters have their own hazards. Always turn off the power or gas before draining, and let the water cool for several hours before you start.

  • Electric heaters: switch off the breaker — never run an electric heater with an empty tank, or the heating elements will burn out.
  • Gas heaters: turn the gas control valve to "pilot" or "off".
  • Let the water cool for at least a few hours before draining.
  • Wear gloves and closed-toe shoes, and keep children and pets away from the work area.

How to Flush a Tank Water Heater

Flushing is straightforward and takes about an hour, most of it waiting for the tank to drain.

  • Turn off the power or gas, and shut off the cold water supply valve at the top of the heater.
  • Attach a garden hose to the drain valve at the bottom of the tank and run it to a floor drain or outside — the water will be hot.
  • Open a hot water faucet somewhere in the house to let air in, then open the drain valve.
  • Let the tank drain completely, then briefly open the cold water supply to stir up and flush out remaining sediment. Repeat until the water runs clear.
  • Close the drain valve, remove the hose, open the cold water supply, and let the tank fill completely before turning the power or gas back on.

Check the Anode Rod

The anode rod is a metal rod inside the tank that sacrifices itself to corrosion so the tank doesn't. When it is worn down to the steel core — usually after 3–5 years — the tank itself starts corroding. Check the rod every 2–3 years by unscrewing it from the top of the tank. If more than 6 inches of the core wire is exposed or the rod is coated in calcium, replace it. A new anode rod costs $20–$50 and is one of the best investments in your water heater's lifespan.

Test the Temperature and Pressure Relief (TPR) Valve

The TPR valve is a critical safety device that releases pressure if the tank overheats. Test it once a year by lifting the lever briefly — water should flow out of the discharge pipe, then stop when you release the lever. If no water comes out, or if it keeps leaking afterward, the valve needs replacing. A faulty TPR valve is a safety hazard, so don't ignore it.

Tankless Water Heater Maintenance

Tankless heaters don't have a tank to flush, but they still need annual descaling to remove mineral buildup from the heat exchanger. The process uses a small pump to circulate white vinegar through the unit for about an hour. Many manufacturers sell descaling kits, and the owner's manual has model-specific instructions. In hard-water areas, descaling twice a year keeps the unit efficient.

When to Call a Plumber

Call a licensed plumber if the drain valve is stuck or leaking, if the water coming out is rusty or smells like rotten eggs, if the TPR valve fails its test, or if you're not comfortable working around gas or electrical connections. A plumber can also perform a full water heater inspection, replace the anode rod, and advise whether an aging unit is worth maintaining or should be replaced.

Frequently Asked Questions

How often should I flush my water heater?

Once a year for most homes, twice a year if you have hard water. Annual flushing is also a condition of many manufacturer warranties.

What happens if I never flush my water heater?

Sediment builds up, efficiency drops, energy bills rise, and the tank corrodes faster. A neglected water heater can fail years early — and a failed tank can flood your home.

How long does it take to flush a water heater?

About an hour in total, including draining time. The hands-on work is only about 15 minutes; the rest is waiting for the tank to empty and refill.

Can I flush a water heater myself?

Yes — most homeowners can do it with a garden hose and basic tools. If you have a gas heater and are unsure about the gas valve, or if anything looks damaged, call a plumber instead.

Editorial Note: This guide is for informational purposes only. Plumbing systems can be dangerous. Always consult a licensed professional for any plumbing repairs or installations.