Leaky Outdoor Faucet? Hose Bib Repair & Winter Protection
An outdoor faucet — also called a hose bib or sillcock — usually leaks because the rubber washer inside has worn out, the packing nut around the handle has loosened, or the valve seat has corroded. A drip from the spout points to a worn washer; water leaking from behind the handle points to the packing. Most hose bib leaks are cheap, quick repairs, but a faucet that leaks inside the wall or keeps dripping after a washer change may be cracked from freezing and need replacing.
First: Find Exactly Where the Leak Is Coming From
Before you fix anything, find where the water is escaping — each leak location has a different cause and repair.
- Dripping from the spout with the handle fully closed — the washer or valve seat has failed.
- Leaking from around the handle stem when the faucet is on — the packing nut is loose or the packing is worn.
- Water from the wall connection or inside the house — the pipe or faucet body may be cracked from freezing.
- Leaking from the vacuum breaker cap on top — the small rubber seal inside it has failed and needs replacing.
- Water spraying from a cracked hose connection — check the hose washer in the coupling before blaming the faucet.
Leaking From the Spout: A Worn Washer
The most common outdoor faucet leak is a steady drip from the spout, and the cause is almost always the rubber washer at the end of the valve stem. Each time you turn the handle, the washer presses against a metal valve seat to shut off the water. After years of use and exposure to sun, heat, and freezing cold, the rubber hardens, cracks, or wears thin. Once the washer can no longer seal against the seat, water seeps past it and drips from the spout even when the handle is fully closed. To replace it, shut off the water, unscrew the packing nut, pull out the stem, and swap in a new washer of the same size. If the valve seat itself is pitted or corroded, a new washer will not seal — the seat must be resurfaced with a seat wrench or the whole faucet replaced.
Leaking From the Handle: A Loose Packing Nut
If water leaks from around the handle stem while the faucet is running, the packing is the problem. The packing is a ring of material (often waxed string or a rubber seal) compressed by the packing nut around the stem to keep water from escaping along the handle shaft. Over time it dries out and shrinks, or the nut works loose. The fix is usually simple: hold the faucet body steady and turn the packing nut clockwise a quarter-turn at a time until the leak stops, without overtightening — the handle should still turn smoothly. If tightening fails, the packing is worn: remove the nut, wrap new packing around the stem, and retighten.
Leaking Inside the Wall: A Cracked Pipe
A leak that appears inside the house, stains the wall behind the faucet, or shows up as dampness in the basement ceiling below it is the most serious kind. It usually means the faucet body or the pipe behind it has cracked — most often because water was left in the line during a freeze and expanded as it turned to ice. This is not a washer repair: the faucet must be replaced, and any damp drywall or insulation must be dried out to prevent mold. If you see water inside the wall, shut off the water to that faucet at its interior shutoff valve right away and call a plumber.
How to Replace an Outdoor Faucet
Replacing a hose bib is manageable for a confident homeowner when the faucet is threaded onto the pipe; if it is soldered on, it is a plumber's job.
- Shut off the water at the interior shutoff valve and open the faucet to drain the line.
- Unscrew the old faucet with a pipe wrench, holding the pipe steady so you do not twist it inside the wall.
- Wrap the pipe threads with Teflon tape, winding clockwise so the tape tightens as you screw the faucet on.
- Thread the new faucet on by hand, then tighten with a wrench until snug and the spout points down.
- Turn the water back on slowly and check every connection for leaks, including inside the wall.
- If the old faucet is soldered on, or the pipe inside the wall is damaged, call a plumber — soldering near a wall needs a torch and fire precautions.
Frost-Free Hose Bibs: Worth the Upgrade?
A frost-free hose bib (also called a freeze-proof sillcock) moves the actual shutoff valve 8 to 12 inches inside the house, so the water stops well behind the exterior wall where it stays warm. When you turn it off, water drains out of the exposed part, leaving nothing to freeze and expand. For homes in cold climates, it is cheap insurance against a burst pipe: the part costs $30–$60, versus hundreds or thousands of dollars in water damage from a split pipe inside a wall. The one rule is disconnecting the garden hose before winter — a connected hose traps water in the faucet, and even a frost-free bib will freeze and crack. If your home still has a standard hose bib, upgrade to a frost-free model before the first freeze.
How to Winterize Your Outdoor Faucet
A few minutes of preparation each fall protects your faucet and the pipe behind it from freeze damage. Do it before the first hard freeze, not after.
- Disconnect all garden hoses, drain them, and store them indoors or in the garage.
- Shut off the water to each outdoor faucet at its interior shutoff valve, usually in the basement or utility room.
- Open the outdoor faucet and leave it open so remaining water can drain out.
- If the shutoff valve has a bleeder cap, open it to drain the line between the valve and the faucet, then close it.
- Fit an insulated foam faucet cover ($5–$10) over each outdoor faucet.
- In spring, turn the interior valve back on slowly and check the faucet and the wall behind it for leaks before reconnecting a hose.
When to Call a Professional
Call a plumber if water is leaking inside the wall, if the faucet is soldered onto the pipe, if a new washer does not stop the drip, or if the pipe behind the faucet is cracked from freezing.
What a Plumber Will Do
A plumber replaces the washer or packing for simple leaks, swaps in a new frost-free hose bib when the faucet is damaged, and repairs any cracked pipe inside the wall — then tests the line and shows you how to winterize it.
Frequently Asked Questions
Why does my outdoor faucet leak even when it is turned off?
A faucet that drips with the handle fully closed almost always has a worn washer or a damaged valve seat. The washer can no longer press tightly enough against the seat to stop the water, so a slow drip continues. Replacing the washer usually fixes it; if the drip persists, the seat is pitted and the faucet needs replacing.
How much does it cost to replace an outdoor faucet?
A professional replacement typically costs $150–$350 for a standard hose bib, including parts and labor. A frost-free model costs a little more, $200–$450 installed. If the pipe inside the wall is cracked or water damage needs repair, the total will be higher.
Can I fix a leaking hose bib myself?
Yes, if the leak is a worn washer or a loose packing nut — both are simple repairs with basic tools and parts that cost under $10. If the faucet is soldered on, the pipe is cracked, or water is leaking inside the wall, hire a plumber. Those repairs involve soldering or opening the wall, which are easy to get wrong.
Should I leave an outdoor faucet dripping in freezing weather?
No — that advice applies to indoor faucets on exterior walls, not outdoor hose bibs. An outdoor faucet should be shut off at the interior valve, drained, and left open with the hose disconnected before winter. Leaving it dripping wastes water and can still freeze the line.
What is the vacuum breaker on an outdoor faucet for?
It is a small backflow preventer that stops dirty water from a garden hose from being siphoned back into your drinking water supply. If it leaks, the rubber seal inside the cap has failed and the cap or the whole breaker needs replacing.
