How to Fix a Leaky Faucet
Most leaky faucets are fixed by replacing a worn washer, O-ring, or cartridge — a repair that costs just a few dollars in parts and takes under an hour. The exact fix depends on your faucet type: compression, ball, cartridge, or ceramic disc.
Before You Start
Turn off the water supply to the faucet using the shutoff valves under the sink. If there are no shutoff valves, turn off the main water supply. Plug the drain so small parts don't fall in, and take a photo of the faucet assembly before you take it apart so you can reassemble it correctly.
Identify Your Faucet Type
There are four main types of faucets, and the repair depends on which one you have. If you're unsure which type you have, take a photo of the faucet and the parts you remove to the hardware store — staff can help you match the replacement parts.
- Compression faucets — the oldest style, with separate hot and cold handles that turn multiple times. They use a rubber washer that compresses against a valve seat.
- Ball faucets — single-handle faucets common in kitchens, with a ball mechanism inside.
- Cartridge faucets — single- or double-handle faucets with a cartridge that controls water flow. Very common in modern homes.
- Ceramic disc faucets — single-lever faucets with two ceramic discs. Durable and long-lasting, but the discs or seals can wear out.
Fixing a Compression Faucet
Compression faucets almost always leak because of a worn rubber washer. After turning off the water, remove the handle (usually a screw under a decorative cap), then unscrew the packing nut and the valve stem. At the bottom of the stem you'll find the washer, held on by a small screw. Remove it, take it to the hardware store to match the exact size, and install the new washer. Reassemble in reverse order, turn the water back on slowly, and check for leaks. If the faucet still leaks after a new washer, the valve seat may be corroded — a valve seat wrench can smooth a rough seat, or you can replace the seat entirely.
Fixing a Ball Faucet
Ball faucets have several parts that can wear out: the ball itself, the cam, the packing, the O-rings, and the inlet seals and springs. A repair kit for your faucet brand (usually $10–$20) includes all of these parts and is the easiest fix. Remove the handle, unscrew the cap, and lift out the cam, ball, and seals. Replace all the parts in the kit, following the included instructions. Pay attention to the alignment of the ball — it has a slot that must line up with a pin inside the faucet body.
Fixing a Cartridge or Ceramic Disc Faucet
Cartridge and ceramic disc faucets are the simplest to repair: you just replace the cartridge or the disc assembly. Remove the handle, then the retaining nut or clip that holds the cartridge in place. Pull the cartridge straight out — note its orientation, because the new one must go in the same way. Take the old cartridge to the hardware store to get an exact match (cartridges are brand- and model-specific). For ceramic disc faucets, you may only need to replace the rubber seals under the discs; if the ceramic discs themselves are cracked or scored, replace the whole disc assembly.
When to Call a Plumber
Call a licensed plumber if the faucet still leaks after replacing the washer or cartridge, if you find corroded or damaged valve seats or pipes, or if the shutoff valves under the sink are stuck or leaking. A plumber can also replace the entire faucet if the old one is worn out — a new faucet installation typically costs $200–$500 including labor. Costs vary by location and job.
Preventing Future Leaks
Don't overtighten faucet handles — that wears out washers and cartridges faster. If you have hard water, mineral deposits accelerate wear on faucet parts; a water softener can extend the life of your fixtures. Fix small drips promptly: a drip that seems minor today can become a steady stream, and a faucet dripping once per second wastes more than 3,000 gallons of water per year.
Frequently Asked Questions
Why does my faucet drip even when it's turned off?
The most common cause is a worn washer, O-ring, or cartridge that no longer seals properly. Replacing the worn part usually fixes the drip.
How much water does a leaky faucet waste?
A faucet dripping once per second wastes more than 3,000 gallons per year. A steady stream wastes far more.
How do I know what replacement cartridge I need?
Remove the old cartridge and take it to the hardware store, or note the faucet's brand and model number (often printed on the faucet or in the manual). Cartridges are brand-specific, so an exact match matters.
Is it better to repair or replace an old faucet?
If the faucet is in good condition and only needs a washer or cartridge, repair it. If the faucet is corroded, the finish is damaged, or it keeps leaking after repairs, replacement is usually the better value.
