Dishwasher Not Draining? 7 Causes & Fixes That Work
A dishwasher that will not drain usually has a clogged filter, a blocked drain hose, a clogged air gap, or — after a new garbage disposal install — a knockout plug that was never removed. Start with the simple checks: clean the filter, run the garbage disposal, and look for kinks in the drain hose. If the dishwasher still holds water after those steps, the drain pump or check valve may have failed, and a plumber or appliance technician should take over.
First Checks Before You Start
Before you take anything apart, rule out the simple causes. Run the dishwasher on a short cycle and listen: if you hear the drain pump humming but the water stays, the pump is working and the blockage is downstream. If you hear nothing, the pump may not be running at all. Check that the drain cycle actually finished — a cycle interrupted by a power cut or a door left ajar will leave water behind. Also run your garbage disposal for 30 seconds: the dishwasher drains through the disposal in most kitchens, and a full disposal can back water up into the dishwasher. Finally, check whether the kitchen sink is draining slowly too — if it is, the clog is in the shared drain line, not the dishwasher itself.
1. Clogged Filter
The filter at the bottom of the dishwasher tub catches food scraps, and it is the number one cause of draining problems. Pull out the bottom rack, twist out the cylindrical filter, and rinse it under running water while scrubbing with a soft brush. If it is coated in grease, soak it in hot soapy water for 10 minutes. Clean the filter monthly and scrape plates before loading — dishwashers are not garbage disposals, and heavy food debris will clog the filter again quickly.
2. Blocked or Kinked Drain Hose
The drain hose runs from the dishwasher to the garbage disposal or sink drain, and it can kink, clog, or sag. Look under the sink and follow the hose: straighten any kinks, and make sure the hose loops up high under the sink (the high loop) before dropping to the drain — this prevents sink water from flowing back into the dishwasher. If the hose is clogged with grease or food, disconnect it (with a bucket underneath) and flush it with hot water. A cracked or brittle hose should be replaced rather than repaired.
3. The Garbage Disposal Knockout Plug
If your dishwasher stopped draining right after a new garbage disposal was installed, the cause is almost certainly the knockout plug. New disposals ship with a small plastic plug sealing the dishwasher inlet, and the installer must knock it out before connecting the drain hose. If it was left in place, the dishwasher has nowhere to drain. Disconnect the hose from the disposal, tap the plug out with a screwdriver and hammer, retrieve the plastic piece from inside the disposal, and reconnect the hose.
4. Clogged Air Gap
The air gap is the small chrome cylinder on the sink next to the faucet, required by code in many states. It prevents dirty water from siphoning back into the dishwasher. If it is clogged with food debris, water backs up into the dishwasher and may spill out of the air gap onto the counter. Pop off the cap, remove the inner cover, and clear out any debris. Flush it with hot water before reassembling.
5. Faulty Drain Pump
The drain pump pushes water out of the tub at the end of each cycle. If the dishwasher is quiet during the drain phase, the pump motor may have failed; if it hums but does not pump, something may be jammed in the impeller. With the power off, you can remove the lower spray arm and filter to check for glass, bones, or debris around the pump inlet. Pump replacement is a job for a technician — it involves removing the dishwasher and working with electrical connections.
6. Drain Valve and Check Valve Problems
Some dishwashers have a drain solenoid valve that opens to let water out, and a check valve that stops it from flowing back. If the solenoid fails, the valve stays shut and the tub holds water; if the check valve fails, dirty water flows back in after draining, so the dishwasher looks full again an hour after a cycle. Both parts are inexpensive, but reaching them requires pulling the dishwasher out from under the counter and working underneath the unit. If you have ruled out the filter, hose, air gap, and disposal plug, these valves are the next suspects — and a technician can test them with a multimeter in minutes.
7. When to Call a Plumber
Call a plumber if the dishwasher still will not drain after cleaning the filter, checking the hose, and clearing the air gap — especially if the kitchen sink is also draining slowly, which points to a clog in the shared drain line rather than the dishwasher itself. A plumber can snake the drain, check the disposal connection, and confirm whether the problem is plumbing or appliance. If the drain system is clear, an appliance technician should test the pump and valves.
When to Call a Professional
Call a plumber if the dishwasher still holds water after you clean the filter, check the hose, and clear the air gap — especially if the kitchen sink drains slowly too, which points to a clogged shared drain line.
What a Plumber Will Do
A plumber snakes or hydro-jets the kitchen drain line, checks the disposal and air gap connections, verifies the drain hose routing, and confirms whether the fault is plumbing or a failed dishwasher pump.
Frequently Asked Questions
Can I run the dishwasher if it is not draining?
It is best not to. Running cycles adds more water to the tub, which can overflow onto the floor and grow mold inside the machine. Fix the drain problem first, then run a cleaning cycle.
How do I drain a dishwasher manually?
Scoop out the standing water with a cup and sponge, then run the drain-only or cancel cycle. If the pump works but the drain is blocked, manually emptying the tub lets you access the filter and pump area safely.
Why is there water in the bottom of my dishwasher after a cycle?
A small amount of water (under an inch) is normal — it keeps the seals from drying out. More than that means a drainage problem: check the filter, drain hose, air gap, and garbage disposal first.
Is a dishwasher drainage problem a plumber or appliance repair job?
It depends on the cause. Clogs in the drain line, disposal connection, or air gap are plumbing jobs. A failed pump, solenoid, or control board is an appliance repair job. A plumber can tell you which one you need.
Why does my dishwasher fill with dirty water when I run the sink?
The drain hose is missing its high loop or the check valve has failed, letting sink water flow back into the dishwasher. A plumber can reroute the hose and replace the check valve.
